چیسس اور ٹرانسمیشن ڈرائیو ایکسل ، اسٹیئرنگ آئل کی مقدار چیک

1. Check the chassis leakage
& nbsp; & nbsp; & nbsp;Check the gearbox and other parts of the chassis to see if there is any leakage, and if it is found, it should be eliminated.
& nbsp; & nbsp; & nbsp;Check the damage of the brake pipeline and power steering system pipeline, and there must be no leakage of liquid or air. If the pipeline is leaked or damaged, it should be repaired or replaced.
& nbsp; & nbsp; & nbsp; & nbsp;Second, replace the transmission gear oil
& nbsp; & nbsp; & nbsp;Due to the improvement of manufacturing technology, the reliability of the transmission is relatively high, and it is generally not prone to failure and damage. During the inspection, the parts such as oil leakage, dust cover and seals should be inspected. If damage or sealing performance is found to be damaged, it should be repaired or replaced.
& nbsp؛ & nbsp؛ & nbsp؛ 1. آئل لیول انسپیکشن ہول کا سکرو پلگ کھولیں ، چیک کریں کہ آیا تیل کی سطح مخصوص تیل کی سطح تک پہنچتی ہے یا نہیں ، اور سوراخ کی طرف O -15 ملی میٹر کے پیمانے کو چیک کریں۔ اگر تیل کی مقدار ناکافی ہے تو ، تیل کی سطح کو مخصوص پیمانے پرپہنچانے اور تیل کی رساو کی جانچ پڑتال کے ل the گیئر آئل بنائیں۔
& nbsp; & nbsp; & nbsp;2. When changing the gear oil, start the vehicle first, run or drive a certain distance to make the transmission gear oil warm up. While the gear oil is still warm, unscrew the oil drain plug to drain the gear oil. When installing the oil drain plug, pay attention to that the oil drain plug of some models is magnetic. After removing the iron powder adsorbed on the screw plug, screw it firmly. Then add new gear oil that meets the requirements until the gear oil overflows from the oil level inspection hole, and install the inspection hole plug.
& nbsp; & nbsp; & nbsp;The gear oil of the transmission of the Jetta car does not need to be replaced during use, just check for leakage. If the transmission is found to be leaking, repair the leak and add gear oil.
& nbsp; & nbsp; & nbsp;3. Inspection and replacement of drive axle gear oil
& nbsp؛ & nbsp؛ 1. تیل کی سطح کے معائنہ کے سوراخ کے سکرو پلگ کو کھولیں اور جانچ کریں کہ آیا تیل کی سطح کے معائنہ کے سوراخ کی سمت میں تیل کی سطح O -15 ملی میٹر تک پہنچتی ہے یا نہیں۔ اگر تیل کی مقدار ناکافی ہے تو ، گیئر آئل کو دوبارہ بھریں جب تک کہ گیئر آئل برتھ انسپیکشن سوراخ سے نہ بہ جائے۔
& nbsp; & nbsp;2. Change the gear oil, start the vehicle for a certain distance, and warm up the axle gear oil. While the gear oil is still warm, remove the oil drain plug to release the gear oil. After draining the gear oil, wipe the screw plug and screw it back firmly into the axle housing. Then unscrew the oil level inspection hole plug, add new gear oil until the gear oil overflows from the oil level inspection hole, and finally install the inspection hole screw plug.
& nbsp; & nbsp;4. Check and replenish the oil volume of power steering hydraulic oil, and replace the hydraulic oil if necessary
پہلے بجلی کے اسٹیئرنگ آئل اسٹوریج ٹینک کے بیرونی حصے کو صاف کریں اور تیل کی سطح کو چیک کریں۔ اگر تیل کی سطح اونچائی نچلی حد کے پیمانے سے کم ہے تو ، آپ کو اسی طرح کے اسٹیئرنگ ہائیڈرولک آئل کو اوپری حد کے پیمانے (میکس) تک شامل کرنے کی ضرورت ہے۔ شامل کرنے سے پہلے ، رساو کیلئے بجلی کی پائپ لائن کو چیک کریں۔ جب اسٹیئرنگ ہائیڈرولک آئل کو چیک کرتے یا شامل کرتے ہو تو ، تیل کے معیار کی آلودگی کی جانچ پڑتال کریں ، اور اگر اس میں خرابی یا آلودگی پائی جاتی ہے تو اس کو بروقت تبدیل کریں۔ تیل کے ذخیرے والے ٹینک میں داخل ہونے سے گندگی یا دھول کو روکنے کے ل operation آپریشن کے دوران خصوصی خیال رکھنا چاہئے۔
& nbsp;The steps to replace the hydraulic oil in the power steering system are as follows:
& nbsp؛ & nbsp؛ 1. سامنے والے پہیے کو سیدھے - لائن ڈرائیونگ حالت میں رکھیں ، کار کے باڈی کے سامنے کو جیک سے جیک کریں ، تاکہ سامنے کا پہیا آزادانہ طور پر گھوم سکے ، اور فکسڈ بریکٹ کے ساتھ سامنے والے ایکسل کو سہارا دے سکے۔
& nbsp; & nbsp;2. Remove the power steering inlet and outlet oil pipes on the power steering gear. The positions of the oil pipes are shown in Figure 1. Put the oil pipe joints and gaskets in a container with clean power steering hydraulic oil for cleaning; The oil tank cover allows the hydraulic oil to flow out naturally.
& nbsp;3. With the oil pipe removed, turn the steering wheel to the left and right extreme positions repeatedly to remove the old hydraulic oil in the power cylinder and connect it with an oil basin to prevent the hydraulic oil from splashing on other components.
& nbsp;4. After draining the hydraulic oil, the oil pipe should be reinstalled.
& nbsp;5. After filling the oil storage tank with new hydraulic oil, start the engine and run it at idle speed. At this time, the oil level will immediately decrease, so it is necessary to continuously add hydraulic oil. When the liquid level in the storage tank stabilizes, the hydraulic oil should be replenished to the upper limit (or & quot;MAX & quot;) of the storage tank.
6. After the engine speed is increased to medium speed, turn the steering wheel to the left and right several times to make the air in the hydraulic system flow back to the oil storage tank and then be discharged. Therefore, the exhaust operation should be carried out until the bubbles in the oil storage tank are completely Until it disappears, and add hydraulic oil to the upper limit of the dipstick at any time.
7. After finishing the exhaust operation, wipe off the oil stains, turn the steering wheel to the left and right several times, and check whether there is any oil leakage in each part. After placing the front wheel in the straight position, stop the engine rotation, withdraw the bracket, and lower the front wheel. Check again that the hydraulic oil volume has reached the upper limit of the reservoir.